Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
How do you really feel on the subject of How to Install a Bathtub Yourself?
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably challenging project. If the old tub is easily available, the project can move quickly; if you have to open up a wall surface to remove the old tub and also position the new tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. See to it you have certified on your own for the task and also fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to think about using one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will assist you mount a brand-new tub in your shower room if you have actually currently bought a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted accessibility that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of both wooden boards under its feet, put the tub in the called for setting. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub up until the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water and inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill the bath tub and likewise check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been utilized a minimum of when as this will resolve it right into its last position.
Getting ready for the Installment
To start with, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, triggering the water to permeate the wall in between the bath as well as the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece about A Step-by-Step Guide to Installing a Bathtub when doing a search on the search engines. For those who appreciated our blog entry plz be sure to share it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Started Report this page